Cross Connection Control Program

Print
Last Updated on Monday, 28 August 2017 12:34

The City of Pullman has a cross-connection control program to protect the City’s drinking water distribution system from contamination caused by backflow.  This program was established through the City’s Cross-Connection Control Ordianance, adopted in 1992. Under normal conditions, water from the distribution system flows into a consumer’s premises. When backflow occurs, water from the consumer’s premises flows into the distribution system. If that water is contaminated because of activities on the consumer’s premises (for example, addition of rust-inhibiting chemicals to a boiler or use of photo-processing chemicals), the water can carry contaminants into the distribution system, possibly causing illness or even death. 

Backflow diagram

 


Do the requirements apply to me?

If your property has a potential cross-connection or hazard (for example, boiler, chemical feed equipment, irrigation system, an interconnected fire sprinkler system, or building height 40 or more feet above the point of connection/water meter), then the requirements of the Cross-Connection Control Ordinance apply to you. You are required to install an approved backflow prevention assembly and have it tested annually by a Washington State approve Backflow Assembly Tester (BAT).

How do I comply?

All potential cross-connections must be protected with an approved backflow prevention assembly. To be approved for use in Pullman, an assembly must be on the “Approved Backflow Prevention Assemblies” list developed by the University of Southern California Foundation for Cross-Connection Control and Hydraulic Research. The assembly may not be modified or installed in a manner that differs from the configuration tested and approved. New assemblies must be tested immediately after installation by City Staff and once a year thereafter by a BAT hired by the customer. After the initial test, the City will send you a notice when annual testing is due. All testing must be performed by an authorized backflow prevention assembly tester.

When are the annual backflow assembly tests due?

Test due dates are determined by the type of hazard that is being protected.  Backflow assembly devices that are installed on either commercial or residential irrigation systems are due to be tested no later than July 15 each year.  All other devices are due to be tested by October 15 of each year.  The City will send you a notice reminding you that testing is due. 

 


backflow device

Water Customer Responsibilities

The customer is responsible to have each backflow assembly located on their premise tested annually and for submitting an original backflow certification report for each backflow assembly tested (most testers and/or testing companies submit the backflow certification report on behalf of the customer).  The customer is responsible to ensure that a tester who is listed on the State of Washington BAT Public List performs all testing and repairs to the backflow assemblies.  The test report must be delivered to the City of Pullman Maintenance & Operations (M&O) Division within 30 calendar days of the test and no later than the assembly test date.  Most local plumbing companies have a Washington State Backflow Assembly Tester (BAT) on staff.


Backflow tester 1

Testing Company and Tester Requirements

Each testing company and tester of backflow assemblies shall  be listed on the State of Washington BAT Public List  and provide a copy of the documents listed below and notify the M&O Division when changes occur.  Test reports from a tester and/or a testing company having expired documentation will not be accepted.  

Backflow Assembly Testing Report Form

The tester and/or testing company shall supply an original backflow assembly test certification report to the customer at the time the assembly is tested and for submission by the customer to the M&O Division (most customers opt to have the tester and/or testing company provide the certification report to the M&O Division). The test certification report shall be on a form approved for use with the City of Pullman.  Incomplete test reports will not be accepted and all information shall be current and accurate.  Test reports submitted on behalf of the customer must be delivered to the City of Pullman Maintenance & Operations (M&O) Division within 30 calendar days of the test and no later than the assembly test date.

Backflow Test Device Gauge

Test equipment used for the purpose of testing a backflow assembly shall be recognized and approved for such use.  No test gauge shall be used for the testing of a backflow assembly that has not successfully passed a valid calibration test within the 12-month period of the date on the backflow assembly report.  

Each backflow device tester and/or testing company shall forward the M&O Division a valid original calibration test report for each gauge under their control.  The calibration report form shall include the calibration company name, address, telephone number, and the name of the person performing the test and their signature, gauge manufacturer name, gauge model number, gauge serial number, the owner of the gauge and the date of calibration.  The calibration report shall indicate the test standards used in the calibration of the gauge.

 


How do I find a Certified Backflow Assembly Tester?

Many of the local plumbing and landscaping companies have Backflow Assembly Testers on staff.  In addition, The Washington Certifications Services (WCS) website provides a listing of Backflow Assembly Testers by County. 


regulatory

Regulatory References


Social Media and Contact Information

Twitter

FacebookEmail Us
TEL: 509.338.3242